Cutting a Rubber Seal Yourself: How to Make Your Geocache Watertight Again
Cutting a rubber seal yourself works with a sharp utility knife, a firm surface, and precise measuring. You measure directly on the container, cut in one go, and insert the seal without stretching it. But for your geocache, that's only half the battle. A cache only stays watertight when the seal, container, and logbook fit together. That's why we show you both here: the clean cut step by step and the points where a ready-made spare part, a suitable container, or a waterproof logbook from Cachewerk will save you the DIY work and a wet log.
Key Takeaways
- Sharp blade, one cut: Dull blades crush the rubber. The edge frays, and the joint remains leaky.
- Measure on the component, not just the old seal: Old seals are often compressed or stretched and only serve as a rough template.
- Never pull it into the groove: Stretched rubber will shrink back, and that's exactly where the gap will form later.
- Don't DIY O-rings: For PETlings and Bison Tubes, the exact ring size matters. A suitable replacement is the safe solution here.
- The logbook is the last line of defense: A weatherproof logbook will survive even the day when a finder doesn't close the lid properly.
Table of Contents
- Where the seal sits in the geocache
- Tools and materials for a clean cut
- Step by step: Cutting a rubber seal yourself
- Round flat seals for screw lids
- Cutting mitered corners
- Common mistakes and how to avoid them
- Protecting the logbook: Silicone sleeve or waterproof logbook?
- Ready-made parts instead of a DIY project
- Our take on watertight geocaches
- Frequently asked questions
- Sources
Where the seal sits in the geocache
Before you reach for a knife, it's worth looking at what type of seal your cache has in the first place. That determines whether cutting it yourself makes sense.
- Flat seal in a screw lid: A round rubber ring or disc sits in the lid of containers such as film canisters, jars, or tins. These seals are easy to cut yourself.
- Profile seal in click boxes: Food storage and click boxes have a seal running around a groove in the lid. If it tears or becomes brittle, you can replace it with a cut-to-size profile or a strip of round cord.
- Rubber sheet as a base: In ammunition boxes or larger wooden caches, a sheet or strip sometimes provides the seal.
- O-ring in PETlings, Nano containers, and Bison Tubes: Here, a round ring sits in a precisely measured groove. You cannot cut this effectively from sheet material, because even tenths of a millimeter determine whether it's watertight or wet. How to determine the right size is explained in our guide Finding the PETling O-Ring Size. For tubes, our post on Bison Tube Repair will help, and for Nanos, the guide Sealing a Nano Container.
In short: cut flat and profile seals yourself, and replace O-rings with the right part.
Tools and materials for a clean cut
You don't need a workshop. This equipment is sufficient for almost any cache seal:
| Tool | For | What to look out for |
|---|---|---|
| Utility knife with a fresh blade segment | Straight cuts, incisions, profiles | Snap off a segment before cutting |
| Sharp garden or rose shears | Thin, soft seals | Only for soft material; hard rubber will fray |
| Cutting mat or wooden board | Firm, flat surface | No soft surface, or the edge will be crooked |
| Metal ruler | Guide for straight cuts | Place securely so it doesn't slip |
| Compass or template | Round flat seals | Test on cardboard first |
| Fine pen, measuring tape | Marking and measuring | Measure on the container, not just the old seal |
| Isopropyl alcohol, lint-free cloth | Clean the groove and lid | Let everything dry |
| Gloves | Protection from the blade | Always move the blade away from your body |
For outdoor use, the rule for material is: use weather- and UV-resistant rubber in the same thickness as the old seal. If the seal is too thick, the lid won't close properly. If it's too thin, it won't press tightly enough. If you're unsure, place the old seal next to the new material and compare the thickness with a caliper or simply with your thumb.
Step by step: Cutting a rubber seal yourself
1. Remove the old seal and clean the groove
Pry out the old seal with a flat screwdriver or toothpick. Clean the groove and lid of sand, needles, and dirt, wipe with isopropyl alcohol, and let everything dry. A clean, dry groove determines watertightness and durability, because moisture impairs adhesion. Sand and needles quickly end up in the groove of geocaches, so thoroughness pays off here.
2. Measure directly on the container
The old seal shows you the shape and hole pattern, but not always the correct size. It becomes deformed through compression, aging, and stretching. Therefore, measure additionally at the groove or the edge of the lid. For profile seals, place the new strip in the groove as a test and mark the length. Add a few millimeters of extra length, which you can trim later. If it's cut too short, it cannot be salvaged.
3. Mark and secure the material
Mark the cut line with a fine pen. Lay the rubber flat on the cutting mat and secure it with the ruler, a clamp, or a piece of tape. Rubber likes to yield to the blade. Once it's secured, the edge will be straight.
4. Cut in one go
Position the blade vertically and pull it through with even pressure. For thicker material, it's better to cut two or three times along the same line instead of pushing with force. Professionals value this too: the GKFP Technical Guidelines for Stabbearbeitung require an exact, clean cut in the correct length for seal cuts. Slight fraying that does not affect functionality is permissible there. For your cache, this means: it doesn't have to look perfect, but the sealing surface must be smooth.
Tip for very elastic or hard rubber: A slightly warmed knife glides through more easily. Work carefully and only with a blade you can hold securely.
5. Adjust the joint and corners
For seals running around, the ends should meet cleanly. Too much overhang pushes a bulge into the seal, while a cut that is too short leaves an open spot. Trim in small steps until the ends lie flush without tension. How to cut mitered corners in boxes is explained further down.
6. Insert without stretching
Press the seal into the groove instead of pulling it in. Start at one point and work all around. If you stretch the rubber lengthwise when inserting it, the material will stretch and then shrink back later. For a cache exposed to frost and sun, this will become apparent at the latest after the first winter.
7. Test watertightness
Close the container, place a dry piece of kitchen paper inside, and submerge it in a bowl of water for a few minutes. If the paper is dry afterward, the seal fits. If it's damp, check the joint, groove, and lid edge, and make corrections.

Round flat seals for screw lids
For screw lids, you usually need a ring or a full disc. Here's how to do it:
- Make a template: Place the lid on thin cardboard and trace the inner edge. Cut out the cardboard and test it in the lid. Only when it fits should you transfer it to the rubber.
- Outer circle first: Cut the outer circle slowly in several small strokes. It's better to turn the material than the knife.
- Inner circle for rings: For a ring, carefully prick the center and cut outward from there to the line.
- Check the edge: Run your finger over the edge. Trim away any steps or jagged edges with a flat cut.
If you need seals often, you can make a simple circle cutter. In the Hobbybrennen forum, a DIYer describes a seal cutter made from two strips, in which threaded rods serve as stops for a carpet knife blade. The advice there is also: first cut a sample out of thin cardboard.
Cutting mitered corners
Click boxes and wooden caches with rectangular lids need clean transitions at the corners. There are two ways to do this.
Miter cut: For a 90-degree corner, cut both ends at a 45-degree angle so that they meet like a picture frame. A guide from the Hoffmann Group on a miter clamp for window and door seals shows the principle: Start in the middle with a straight cut, work clockwise around the four corners, and end with about 5 mm of extra length. For caches, a utility knife with a set square as a guide is usually sufficient instead of the clamp.
Fold instead of cutting: For small boxes with rounded corners, it's easier to fold the seal around the corner in one piece. Press the profile into the curve without stretching it. If it wrinkles, trim it slightly.

A drop of waterproof adhesive at critical joints prevents the seal from shifting when finders open the lid frequently. For 3D-printed caches, it's worth smoothing the sealing surface itself: Our post on weatherproof PETG geocaches shows how to remove print lines by wet sanding so that the seal lies flat.
Common mistakes and how to avoid them
| Mistake | Consequence | Better this way |
|---|---|---|
| Dull blade | Crushed, frayed edge | A fresh blade segment before every cut |
| Measured only on the old seal | Seal too short or too long | Measure additionally directly on the groove and lid |
| Seal pulled into the groove | Gap at the joint after a few weeks | Press in, don't pull |
| Material too thick | Lid closes with difficulty, finders don't close it completely | Use the thickness of the original seal |
| Sand in the groove | Gap through which water creeps into the cache | Clean, dry, then insert |
| O-ring cut from sheet material | Leaky from the first rain | Use a suitable O-ring in the exact size |
You can save yourself many maintenance visits if you care for the seal regularly. How to do this with O-rings is explained in O-Ring Care for Geocaches.
Protecting the logbook: Silicone sleeve or waterproof logbook?
Many owners additionally place the logbook in a sleeve, such as one made of silicone, or in a small zip-lock bag. The idea is good: A sleeve keeps dirt and condensation away from the paper if the seal ever fails.
The fit depends on three things:
- Snug, but not tight: The logbook should not slip in the sleeve, but should be removable without pulling. If you have to tug, you'll tear the pages.
- Space in the container: The sleeve must not lift the lid or press against the seal. Otherwise, it will do more harm than good.
- Simply back: Finders often push the logbook back in a hurry. A sleeve that can be easily slipped back over it will also be used.
It's most robust if the logbook itself can withstand moisture. Then the sleeve is an extra and not the only rescue. For PETlings, we have our Logwerk Replacement Logbook, a waterproof geocaching logbook made specifically for these containers. For micros, you reach for the long-lasting and robust CacheWerk Micro Logbook.
Ready-made parts instead of a DIY project
Cut-to-size seals are ideal if a lid from your stock needs to become watertight again. But if you're planning a new cache or want to replace a container, ready-made parts will save you time and rework. At Cachewerk, you'll find PETling and magnetic containers, weatherproof logbooks, spare parts, and creative camouflage caches developed and tested by active geocachers for outdoor use.
Browse our Geocaching Equipment and Accessories category or check out our 3D-printed caches and wooden caches. And if you're torn between a screw and magnetic closure, our closure comparison will help you.
Our Take on Water-Tight Geocaches
We're geocachers ourselves and know the feeling: a beautiful cache, a lovingly crafted hiding place, and then a swollen logbook because the seal has failed. Cutting your own seal is a good way to save a container, and we appreciate every owner who takes such care of their caches.
We always think of water-tightness as a system. A hiding place stays dry when the container, closure, seal, and logbook all fit together. That's why we develop and test our caches ourselves for outdoor use, whether 3D-printed from PETG or as a handcrafted wooden cache, and offer weather-resistant logbooks and spare parts to go with them.
Our advice: Feel free to cut flat seals yourself, but use the right O-ring and give your cache a logbook that can withstand moisture. Then you'll have less maintenance and your finders will have more fun. And if you need something special, contact us about a custom-made solution.
Benedikt
Frequently Asked Questions
What's the best tool for cutting rubber?
A sharp utility knife with a fresh snap-off blade on a firm cutting surface. For thin, soft seals, well-sharpened garden or rose shears also work. It's important to secure the material and cut in a single, even stroke.
Can I cut an O-ring for my PETling myself?
We advise against it. O-rings must fit the groove exactly in terms of inner diameter and cord thickness, and you can't achieve that reliably with a knife. It's better to determine the correct size and use a suitable ring.
What can be used as a seal for a geocache?
For flat seals, weather- and UV-resistant rubber with the same thickness as the original seal is suitable. It's important that the seal lies flat and the lid closes without force. For containers with an O-ring, use a suitable ring in the exact size.
How do I cut a seal at a miter?
For a right-angled corner, cut both ends at a 45-degree angle so that they fit together like a picture frame. For cache boxes, a set square is usually sufficient as a guide for the utility knife. For rounded corners, it's better to bend the seal around the curve in one piece.
Does my logbook need a silicone sleeve?
A sleeve provides additional protection against dirt and condensation if it fits snugly and doesn't lift the lid. The safest option is a logbook that can withstand moisture itself, such as a waterproof replacement logbook for PETling containers. Then the sleeve is an extra and not a last resort.
Sources
- GKFP: Technical Guidelines for Woodworking (April 2023)
- Hoffmann Group: Instructions for Miter Clamps for Window and Door Seals
- WIDURO: How can you replace the rubber seal?
- Fensterdichter Meister Uhl: Changing Seals on uPVC Windows
- Hobbybrennen Forum: Seal Cutter
